7 sources, 5 tags

Beginner FAQ

Why Does My CNC or Laser Throw Alarm 2 When I Jog or Start a Job?

ALARM:2 means a move would take your CNC router or laser past the travel limits set in its firmware. Usually the machine wasn't homed, the job origin is wrong, the job doesn't fit, or on a laser, overscan runs off the edge.

ALARM:2 is a soft limit alarm. Your machine’s controller worked out that the next move would take it past the travel limits stored in its firmware, so it refused to make it. It isn’t a CNC-only problem: many hobby diode lasers and routers run Grbl or Grbl-style firmware, and they raise the same alarm for mostly the same reasons.

What the alarm actually says

On Grbl controllers the alarm reads “G-code motion target exceeds machine travel.” The Grbl documentation says the machine keeps its position when this alarm fires and you can unlock it. That’s different from ALARM:1, a hard limit, where a limit switch was physically hit, the position is probably lost and re-homing is strongly recommended.

Soft limits only work when homing is turned on and the maximum travel settings ($130, $131 and $132 for X, Y and Z) are accurate, because the controller has to know where it is to judge whether a move goes too far.

Causes both machines share

  • The machine wasn’t homed. Home every time you connect, and don’t push the gantry or laser head by hand afterward.
  • The travel settings don’t match the machine. If $130-$132 are bigger or smaller than the real travel, the limits are wrong. In gSender they’re under Config > Homing/Limits; in LightBurn they’re in Machine Settings.
  • The job origin doesn’t match the design. On a CNC, the zero you chose in CAM (for example bottom left) has to match where you zeroed the stock. In LightBurn, running in Current Position or User Origin mode without setting the Job Origin or User Origin correctly is one of the causes LightBurn’s documentation lists.
  • The job is bigger than the work area, or it doesn’t fit from where you started it. Move the stock or the start point so the whole job fits.

Causes that are mostly laser problems

  • Overscan. When filling or engraving an image, the laser travels past each line to speed up and slow down. LightBurn’s documentation says those extra moves can take the head outside its limits when the design is near the edge, and the controller answers with ALARM:2. The distance grows with speed. Reduce the speed or the overscan percentage, or move the design toward the middle of the bed. Turn on traversal moves in LightBurn’s Preview window: red lines crossing the green work-area border are the warning sign.
  • Stray shapes. In an August 2026 LightBurn forum thread about an Ortur LM3, one reply suggested using Select All to find tiny forgotten shapes outside the grid, and another called overscan running past the work area the most common cause.
  • Rotary attachments. A Y-axis rotary can be asked to travel farther than the Y limit in firmware. LightBurn suggests turning soft limits off while using the rotary ($20=0) and back on ($20=1) before you return to flat work.

A CNC-specific case

Surfacing a spoilboard uses nearly the full travel, so Sienci Labs suggests turning soft and hard limits off for that one job and back on afterward. On the Sienci forum, a LongMill owner who hit ALARM:2 after upgrading machines was advised to compare their soft limit values with Sienci’s published travel specs and lower any that were larger than the machine.

Don’t just switch soft limits off

Turning off soft limits makes the alarm go away, but it also removes the protection that stops the machine from crashing into its own frame. Use it only for the rotary and surfacing cases above, and fix the origin, travel settings or job size otherwise. If you’re still stuck, copy the exact alarm line from the console and post it with your machine, controller, software version and job origin settings when you ask for help.

Sources

About This Tinkerverse

The Tinkerverse

Lasers, maker tools and whatever else catches a tech geek's curiosity. News, how-tos and projects from The Tinkerverse.

Version
Always tinkering
Memory
640K of curiosity
Status
Probably mid-project
About pageYouTube
Control Panel

Saved on this device

Display

Desktop color

Desktop pattern

Trash

9 items

Secure Access
Command Prompt